CV. ANUGERAH SISTEMA PERKASA

Your total solution for Wire Cut EDM consumables parts and accessories

RUST REMOVER KC-12

DESCRIPTION

  • Water dilutable and economical rust remover

  • Remove rust from wire-cut metal workpieces and other ferrous materials.

  • Appearance : colorless and clear

  • pH(full strength) : less than 1

  • Package size : 6L per pail

HOW TO USE

  • Dilute up to 1-10 depending on the degree of rust on the surface.

Note : Try three-fold dilution first. Then check the degree of rust removal and adjust the dilution accordingly.

  • Soak the rusted workpiece in KC-12.

  • Rinse the product well with water as soon as the rust dissolves.

  • Since rust is likely after rinsing with water, apply a water-replaceable rust preventive agent.

  • If the KC-12 deteriotes, replace it wih new fluid rather than adding more.

  • Use a hard plastic container for soaking the workpiece. Avoid metal container.


RUST REMOVER K-200

DESCRIPTION

  • Removal of rust on metal workpieces, molds and other ferrous materials.

  • Removal of sludge on wire cutting machines.

  • Appearance : green transparent

  • pH(full strength) : less than 1

  • Package size : 6L per pail

HOW TO USE

  • Use undiluted, do not dilute Rust Remover K-200.

  • Use a hard plastic container for soaking the workpiece. Avoid metal container.

Soak and rinse

  • Soak the rusted workpiece in K-200

  • Rinse the product well with water as soon as the rust dissolves.

  • Since rust is likely after rinsing with water, apply a water-replaceable rust preventive agent.

Or

Apply with brush or cloth

  • Apply the remover to the rusty surface using a brush or cloth.

  • As soon as the rust dissolves, rinse the surface with water using another brush or cloth.

  • Since rust is likely after rinsing with water, apply a water-replaceable rust preventive agent.


MECHA PROOF W-2K

DESCRIPTION

  • Rust Preventive

  • Inhibit rust by diluting and adding to wire EDM processing fluid.

  • Rust prevention for wire electric discharge machining.

  • Appearance : Colorless and clear

  • pH(full strength) : 5.1

  • Package size : 5L per pail

HOW TO USE

First dilute -> then add to processing fluid

Dilute :

  1. Collect 10 to 20 liters of processing fluid in a container.

  2. Add the following amount of W-2K to collected fluid on step 1 and mix.

Immersion type machine : 0.2 to 0.5% of machine total tank fluid

Flushing type machine : 0.5 to 0.6% of machine total tank fluid

Add to processing fluid

  1. Pour the diluted fluid above into the tank.

  2. Circulate for about 20 minutes to make the concentration uniform.

Note : When rust prevention effectiveness later decrease ( timing varies depending on usage conditions ), add 5-10% of the amount of W-2K added in step 2 to the tank.


MECHA P-COAT

DESCRIPTION

  • Rust inhibitor ( Aerosol )

  • Rust and corrosion inhibitor for wire EDM during lengthy processing.

  • Prevent rust on workpiece and suppress electrolytic corrosion around wire electrical discharge machines.

  • Appearance : Green

  • Package size : 420 mL per can

HOW TO USE

  • Apply in advance to the entire surface of wire electrical discharge workpieces to prevent rust on the surface.

  • Apply around the wire electrical discharge machine's power supply area and other susceptible areas to suppress electrolytic corrosion.

  • To use, spray the surface lightly and evenly from 20-30 cm away. Let it dry for about 15 minutes to promote adhesion of the film.

Note : Aerosol, do not use near flames